WJCO
Meme King
Thanks. So as far as setting the depth, do you have to knock that race in and out a few times during setup?
In The Shop - Disciple Off Road
- Thread starter Disciple Off Road
- Start date
Disciple Off Road
Hooked
Yes, we can usually get correct depth within 2-3 adjustments though so usually not too bad.
CalSgt
Hooked
I loved the look of my LOD Destroyers…
but, I destroyed one of them the first time out and it destroyed my rocker panel. To be fair it was a pretty extreme situation.
My biggest complaint was that the powder coating flaked off in big pieces as soon as they got a few scratches.
I tried to find pictures of the damage but my camera roll starts at the time when I was replacing them. This one shows the powder coat failing though
ETA: I did a search on here and found a better picture
but, I destroyed one of them the first time out and it destroyed my rocker panel. To be fair it was a pretty extreme situation.
My biggest complaint was that the powder coating flaked off in big pieces as soon as they got a few scratches.
I tried to find pictures of the damage but my camera roll starts at the time when I was replacing them. This one shows the powder coat failing though
ETA: I did a search on here and found a better picture
Disciple Off Road
Hooked
Holy cow you aren’t kidding! And definitely looks like they took a hard hit.
CalSgt
Hooked
I had to winch over something kinda crooked and that was the pivot point
bobfriesenhahn
Hooked
They are described as a "medium duty" slider.
CalSgt
Hooked
LOL… Thanks Bob, I’ll be more careful
Disciple Off Road
Hooked
Took delivery of this beautiful Granite Crystal 392 today ready for long arms, 4.5” lift and big FOXshocks.
This one is also playing off the factory gold accent colors with these custom gold KMC Grenades on 38” Nitto Trail Grapplers.
This one is also playing off the factory gold accent colors with these custom gold KMC Grenades on 38” Nitto Trail Grapplers.
Cousin Clyde
Hooked
As in: this is your jeep?
Disciple Off Road
Hooked
Negative but I wouldn't complain if it was! The rebuild of our JK is coming very soon.
bobfriesenhahn
Hooked
Lotsa bling bling bling!
Lperdue
Active Member
Yep hopefully we’ll have the wife’s rig in your shop sometime at the start of the year. Either for gears or coil overs still debating on which route to go first.
Disciple Off Road
Hooked
Sounds great look forward to it!
cosmokenney
Caught the Bug
What's the overall length on those bars? I just installed MetalCload steering parts and need to make some bars for myself and I'm not sure what a good length would be.
Brute
Hooked
I like that color combo…
CalSgt
Hooked
They’re either 3 or 4 foot long, whatever Ace or tractor store had in stock.
Disciple Off Road
Hooked
This 392 is going home tomorrow and really happy with the way it turned out. It drives great with the DTD/Long Arms and really liking the 4.88 gears with the 38's. We also added the EVO slider rock lights which are crazy bright and work really well.
We did the RockJock high steer kit with knuckles and as you can see, raises up the steering quite a bit. With mixing aftermarket parts that weren't designed together (DTD brackets and RockJock High Steer), we had to get creative with getting everything to cycle properly, especially the ram assist. Only place the PSC would work was under the tie rod so we will be making a skid plate for it. You can also see the links are bent inward which was needed to clear the steering linkage at full lock/stuff and droop. Needless to say, everything gets super tight!
Rear aftermarket bumper was added along with with EVO HD tire carrier.
With the EVO HD tire carrier, we again used the Teraflex camera mount which works great. And of course some 38" Trail Grapplers and Method Beadlocks.
The EVO rear JL/JLU inner fenders are now available to order...finally! They really finished off the rear inner wheel wells. These didn't require any trimming or modifications even with the bolt on coilovers.
We also added an ARB Twin compressor under the passenger seat using the GRIMM mount. Super clean setup allowing you to have access to the air chuck and switch on the side of the seat. Kind of nice that you don't have to use a stock AUX stich or the like for the compressor.
Only thing we are going to change is add some heavier rate coils in the rear. The front uses the HD 392/Diesel 400 lower coil that are a 400 but the rear still uses a 200/200 which is crazy light. We had to add a ton of preload just to get it sitting close to level.
We did the RockJock high steer kit with knuckles and as you can see, raises up the steering quite a bit. With mixing aftermarket parts that weren't designed together (DTD brackets and RockJock High Steer), we had to get creative with getting everything to cycle properly, especially the ram assist. Only place the PSC would work was under the tie rod so we will be making a skid plate for it. You can also see the links are bent inward which was needed to clear the steering linkage at full lock/stuff and droop. Needless to say, everything gets super tight!
Rear aftermarket bumper was added along with with EVO HD tire carrier.
With the EVO HD tire carrier, we again used the Teraflex camera mount which works great. And of course some 38" Trail Grapplers and Method Beadlocks.
The EVO rear JL/JLU inner fenders are now available to order...finally! They really finished off the rear inner wheel wells. These didn't require any trimming or modifications even with the bolt on coilovers.
We also added an ARB Twin compressor under the passenger seat using the GRIMM mount. Super clean setup allowing you to have access to the air chuck and switch on the side of the seat. Kind of nice that you don't have to use a stock AUX stich or the like for the compressor.
Only thing we are going to change is add some heavier rate coils in the rear. The front uses the HD 392/Diesel 400 lower coil that are a 400 but the rear still uses a 200/200 which is crazy light. We had to add a ton of preload just to get it sitting close to level.