What was done to your rig this week?

TheFett · May 3, 2016

AllAmericanInfidel said:
Lol I was just curious, nothing more. I'll be regearing to 4.88s as well and initially run 35s, then possible bump to 37s when I get the front axle swapped out. I hope I have the same results. I used a ProCal in the past and considering the Superchips Flashcal this time around.

Hey I take no offense, I just wanted to make sure you guys didn't think it was coming from some crazy sun burnt Floridiot down here......lol I'm crazy but not that crazy....lol Yeh man, my brother did the ProCal and loved it, I went the Superchips FlashPaq and have loved it since. I usually always or at least recently as I've been driving more have my FlashPaq set to Econ mode for the best fuel mileage possible, even did that with the 37's and thats the best I was getting. Shameless plug too, G2 gears are what I went with and my brother went with Yukon gears and seemed to be louder than mine, so I'd have to say very happy with G2's as well. JMO

Jeepfan30 · May 3, 2016

TheFett said:
G2 gears are what I went with and my brother went with Yukon gears and seemed to be louder than mine, so I'd have to say very happy with G2's as well. JMO

My Yukon 4.56 are just as quiet as stock after me and a friend set them up properly. They were a little noisier after the "professional" install that resulted in a front pinion bearing being toasted. After we replaced all the bearings and set the Yukons up to spec, I am amazed they are so quiet. I think you should have a quiet gear set with any brand if they are set up to spec.

swampdog · May 3, 2016

Jeepfan30 said:
I think you should have a quiet gear set with any brand if they are set up to spec.

This is true.

Zachp28 · May 3, 2016

geberhard said:
Looks good! What is the chain in the front bumper for?

Well it was once used to drag a 2wd Silverado out of some mud.. other than that, its pulled shrubs out of the ground. Thats it so far haha. Never know what you'll need a shitty little chain for, other than to be criticized for it haha.

compoint · May 3, 2016

Weekend project

compoint · May 3, 2016

New fender flares

Desert Rose JK · May 3, 2016

I also installed a set of Bushwacker fender flares...

aribelin · May 3, 2016

Finished installing my Genright high fender kit, lots of cutting on the tub to get clearance for 39's:

AND, trying to get this project finished up:

RageKage · May 3, 2016

TheFett said:
Just you guys don't think the sun has gone to my head down here I'm not making this up I swear!

View attachment 201440

Prolly shouldn't be taking a pic of your dash at 70 mph [emoji23]

RockyJk · May 4, 2016

aribelin said:
Finished installing my Genright high fender kit, lots of cutting on the tub to get clearance for 39's:

AND, trying to get this project finished up:

View attachment 201533

That thing is badass! LS swap?

BdugJK · May 4, 2016

Zachp28 said:
Knocked out a 4 inch lift.. new steering stabilizer, new front calipers, brakes all the way around, and cleaned it up a bit..

Um yeah jeep is awesome, but the beard gets a 10. Haha digging it man work won't allow me, maybe after retirement. :rock:

aribelin · May 4, 2016

RockyJk said:
That thing is badass! LS swap?

Yes, 6.0L - L96/6L80.

Evil · May 5, 2016

AllAmericanInfidel said:
Awesome! I can't wait to see the finished products. I am likely going with the same front bumper and the EVO low angle sliders. I'm still on the fence about the EVO PRO rear bumper. Can't wait to see some good pics of it! Looking great so far!

Its never going to be done! Ill get a pic of the rear tomorrow. Im in the process of swapping out tires so I have shit everywhere.