What was done to your rig this week?

Installed a Toys by Troy stinger and a set of Coverking seat covers
 

Attachments

  • Coverking Seat Covers.jpg
    Coverking Seat Covers.jpg
    86.3 KB · Views: 343
  • TBT1.jpg
    TBT1.jpg
    188.5 KB · Views: 320
little squeak every time you go straight lol? i have to do mine in the next couple days post up some picks of your swap! are you changing all the breaks and stuff as well?

Dang that squeak! Lol Plus one side of my axle was leaking in conjunction with the squeak. I've already did the install, my phones camera was jacked up at the time & wouldn't focus so I didn't take many pictures. The install took me less than an hour thanks to Eddies right up. It was pretty straight forward. Make sure you get the shafts with the Bearings already pressed on that made life so much easier. If you decide to go with the Ten Factory ones they are 414$ at Northridge with the discount...I did replace the rear pads & rotors I figured after 112k it was time. Lol

Here's that right up Eddie did. http://wayalife.com/showthread.php?...-Axle-Shaft-Removal-amp-Installation-Write-Up
 
Dang that squeak! Lol Plus one side of my axle was leaking in conjunction with the squeak. I've already did the install, my phones camera was jacked up at the time & wouldn't focus so I didn't take many pictures. The install took me less than an hour thanks to Eddies right up. It was pretty straight forward. Make sure you get the shafts with the Bearings already pressed on that made life so much easier. If you decide to go with the Ten Factory ones they are 414$ at Northridge with the discount...I did replace the rear pads & rotors I figured after 112k it was time. Lol

Here's that right up Eddie did. http://wayalife.com/showthread.php?...-Axle-Shaft-Removal-amp-Installation-Write-Up

i got 4 stock shafts for free and i just bought bearings to rebuild them lol but that squeak omg lol, did you think you pads or rotors were toast from it, I just changed mine like 10k then bent it over the winter?
 
i got 4 stock shafts for free and i just bought bearings to rebuild them lol but that squeak omg lol, did you think you pads or rotors were toast from it, I just changed mine like 10k then bent it over the winter?


Gotcha.....I'm not sure but I would think that your brake pads & rotors should be fine. Mine didn't look like anything was wrong with them just a little wore out from all the miles.
 
Gotcha.....I'm not sure but I would think that your brake pads & rotors should be fine. Mine didn't look like anything was wrong with them just a little wore out from all the miles.

ya didnt want to do everything twice if i have it all off, but also dont wana replace new stuff lol. thanks for the help!
 
Mounted a Powerplant winch that I picked up for $700. It was a tight fit with lots of grinding and drilling. And it is still slightly offset by 3/8". Also raised the rear shock mounts both upper and lower.
ImageUploadedByWAYALIFE1431294141.741585.jpgImageUploadedByWAYALIFE1431294151.971184.jpg
 
Josh. These are the same I've had on my rig for about a year now. Still really happy with them.

Maxxima (M85416R) Red/White Round Rear LED Stop/Tail/Turn/Back-Up Light https://www.amazon.com/dp/B00IZG63DE/ref=cm_sw_r_awd_hyVtvb0TACAWA
https://www.amazon.com/dp/B00IZG63DE/ref=cm_sw_r_awd_hyVtvb0TACAWA

View attachment 142370
View attachment 142371
View attachment 142372

Jason, I have opted for these same lights. Still trying to find time to install the corners. I can't tell in you photos, how did you attach these tail lights?

I've thought about drilling and tapping the corners, or just use two sided emblem tape on the flange.

Edit: I saw the photos in your link and that answered my question. Looks great!
 
Last edited:
Top Bottom