What was done to your rig this week?

[StrizzyChris]

It's a little bit away from the engine pulleys

it always is....until it isnt :yup:

 

[Lake Bum]

Rancho rock ready rear bumper and swing out tire carrier. I thought it came out pretty good.

 

[NV375]

Temporary LED license plate light installed. I got stopped about a mile from the house taking the wife to dinner last weekend. I plan to relocate the plate again when I install a tire carrier later.

 

[GR8WHITE]

I welded on one of my control arm skids. Hopefully tomorrow i can get the other one glued on.

 

[JKbrick]

PowerTank and Carolina Metal Masters steering are on; hard too is off for the week

View attachment 122385View attachment 122386

I have a stupid question. Do you get bump steer? I was under the impression you want your drag link and track bar as parallel as possible. Just curious, not knocking your setup.

 

[Dean454]

Installed new front Core 44 and Adams 1350 rear DS

 

[Grappler]

I have a stupid question. Do you get bump steer? I was under the impression you want your drag link and track bar as parallel as possible. Just curious, not knocking your setup.

Not a stupid question at all. No bump steer or wandering, though I am looking forward to the hydro assist upgrade soon.

 

[Sola_Christos]

Removed factory radio and replaced it with a single din unit and cb; replaced all the speakers and factory amp as well.View attachment 120551

That's clean! Good job with install and selection!

 

[ridg3runner]

Feeble effort to prevent anymore rusting to the poor MJ's roof till I can get the bodywork started. Killed two birds with one stone too, made use of the leftover wrapping paper I've been looking at for the last 3 years.

 

[Gaslight]

Installed Synergy SS brake lines, Fox 2.0 shocks, TF front adjustable track bar, replaced the front rotors/calipers, and pads all around... Busy busy busy.

ATX slots and 35" BFG KM2's next Thursday!

\m/

 

[gtony12]

Installed a new air filter today!

 

[ProtocolJK]

Finally got around to installing my protek oil pan skid!

 

[BadApple]

Did a little tuning up yesterday.
New spark plugs
Spark plug wires
Oil change
Diff fluid change f&r
New thermostat
Radiator flush
Trans flush and tcase flush.

All that being said changinf plug wires sucks.

 

[RockyJk]

Got the dynomax welded on


Also pretty sure I blew out my shocks leaving hammer town earlier

 

[RDE2ROK]

Did a little tuning up yesterday.
New spark plugs
Spark plug wires
Oil change
Diff fluid change f&r
New thermostat
Radiator flush
Trans flush and tcase flush.

All that being said changinf plug wires sucks.

How many miles you got on that jeep? Do you need to change the plugs & wires? There's nothing like the feeling of all new fluids!:thumb:

 

[Yeep]

Dropped it off for some new gears... 5.13's

 

[GR8WHITE]

Got the dynomax welded on
View attachment 123196

Also pretty sure I blew out my shocks leaving hammer town earlier

Which DynoMax muffler? I going to be fabricating my own "offroad" exhaust and i cant decide which one of their muffler to go with.

 

[RockyJk]

Which DynoMax muffler? I going to be fabricating my own "offroad" exhaust and i cant decide which one of their muffler to go with.

I have the ultra flow ss muffler it's not too loud but sounds pretty sweet when you get on it

 

[GR8WHITE]

I have the ultra flow ss muffler it's not too loud but sounds pretty sweet when you get on it

ok cool, I was thinking about the DynoMax VT but i have read some very mixed reviews.

 

[jeeeep]

ok cool, I was thinking about the DynoMax VT but i have read some very mixed reviews.

I have the VT on my 2010, I like it - no drone on the long trips and opens up when needed.

I had a Borla before and got tired of the drone, have run flowmaster on my GC hemi, it was loud...or may be an age thing I'm getting tired of loud mufflers :thinking: