What was done to your rig this week?
- Thread starter 10frank9
- Start date
Rst8rox
Active Member
Thanks! The F&R 4links and Coilovers should be mocked in, flex tested & final welded by end of the week. Than build driveshafts, build center console & dash. Than plumb and wire. Than test & tune!!!
Sent from my iPhone using WAYALIFE mobile app
fiend
Caught the Bug
Installed JK Innovations 4 tire fill kit.
Modified my cabin blower to enable use of replaceable cabin air filters.
Reinforced my track bar brace/PSC mount.
Fixed my loose front bump stop and removed 3/4” of unnecessary bump stop.
Sent from my iPhone using WAYALIFE mobile app
Modified my cabin blower to enable use of replaceable cabin air filters.
Reinforced my track bar brace/PSC mount.
Fixed my loose front bump stop and removed 3/4” of unnecessary bump stop.
Sent from my iPhone using WAYALIFE mobile app
danford.lau
Caught the Bug
That JK innovations system looks neat. Would get it if I didn’t have to also swap from single to dual compressor.
Sent from my iPhone using WAYALIFE mobile app
fiend
Caught the Bug
I think it would work with a single, just would take longer than with a dual.
Sent from my iPhone using WAYALIFE mobile app
Ddays
Hooked
Did you decide what you're gonna do for a side step/sliders?
19YJ94
Caught the Bug
LOD Signature Series sliders (bolt on)
Ruvicon
Member
Please share details. Sounds like a good winter project for me.
Sent from my iPhone using WAYALIFE mobile app
Clifford33
Caught the Bug
Put my new rigid lights on and also removed my rear bumper and installed some reverse lights
Sent from my iPhone using WAYALIFE mobile app
Put some new fogs in and put some red behind the Spyder. 
Sent from my iPhone using WAYALIFE mobile app
Sent from my iPhone using WAYALIFE mobile app
ThatJeepGuy
New member
Painted the wheels and got some new rubbers on. Dismounting was a PITA on the spare. Finally had to give in and find a tire shop to break the inner bead for me.
Clifford33
Caught the Bug
Old banner 
New bannerIt’s kinda hard to tell but my old windshield banner was looking pretty bad so I ordered a new one
thanks Eddie. Looks a lot cleaner now.Sent from my iPhone using WAYALIFE mobile app
Bear_JT
Hooked
Got the Trail Graps mounted up today. Just need to do the spare now.
Sent from my iPhone using WAYALIFE mobile app
Sent from my iPhone using WAYALIFE mobile app
ThatJeepGuy
New member
Finally had time to mount my spare
dhughes16
New member
Changed the spark plugs in my wife’s ‘16 JKU and found some oil I. The upper plenum. What could cause this?
Sent from my iPhone using WAYALIFE mobile app
Sent from my iPhone using WAYALIFE mobile app
ThatJeepGuy
New member
How much oil did you find?
AgBass01
Caught the Bug
I changed mine a few months back and found a little in my upper plenum as well.
Had new gears installed last Friday, went from 3.21 to 4.56. Mechanic told me I have all the signs of the dreaded oil cooler leak, I wondered why I was low on coolant a couple weeks ago.
Sent from my SM-G950U using Tapatalk
dhughes16
New member
Not a whole lot but some from the plenum to the intake manifold. There was none in the actual filter so it hasn’t made it that far and there didn’t seem to be any significant residue in the holes for the lower plenum.
Sent from my iPhone using WAYALIFE mobile app
dhughes16
New member
On my old ‘12 I replaced the oil cooler, but if I remember correctly that wouldn’t leak oil to the intake but create a leak coming from the top of the transmission bell down towards the bottoms of the Jeep
Sent from my iPhone using WAYALIFE mobile app