OverlanderJK
Resident Smartass
Factory axles. If it hits you can grind down the ears on the shaft a bit. I did on my D30 and never had issues.
Sent from my iPhone using WAYALIFE mobile app
What was done to your rig this week?
- Thread starter 10frank9
- Start date
Factory axles. If it hits you can grind down the ears on the shaft a bit. I did on my D30 and never had issues.
Sent from my iPhone using WAYALIFE mobile app
JKbrick
Active Member
I wondered, if I ever broke an axle it will probably be from old age not hard use no more than I get time to drive it
Sent from my iPhone using WAYALIFE mobile app
SDG
Caught the Bug
Time to clean up the sliders. Been a year or 2, and they were starting to get rusty.
Took the angle grinder with a wire wheel to them to knock off the rust etc.
Then hand sanded down the pain so there would be a smooth transition... and coated with rust inhibitor. Has to sit for 24h, then give another light sanding.
Plan on using rustolium, but bought a quart so I can roll it on. Last time I got A ton of overspray even after covering half the jeep in news paper. We will see how this technique works out.
Took the angle grinder with a wire wheel to them to knock off the rust etc.
Then hand sanded down the pain so there would be a smooth transition... and coated with rust inhibitor. Has to sit for 24h, then give another light sanding.
Plan on using rustolium, but bought a quart so I can roll it on. Last time I got A ton of overspray even after covering half the jeep in news paper. We will see how this technique works out.
JAGS
Hooked
Looks like fun. [emoji15] Mine look like shit too. They are scratched, rusted and dented. May tackle my corners and rockskins in the next few weeks while I'm at it.
Overspray sucks. I tape off like crazy. Use a cardboard shield and pull into the garage a bit to deflect any wind.
I'll be using VHT roll bar and chassis paint.
MET5
New member
Attachments
BobNH
Member
Hope you went with the Spicer joints. If you did go with gold seals, keep an eye on them. It appears their quality has gone down over the years. YMMV, and I hope it does. It was my only disappointment with my TW for my TJ.
Sent from my SM-N910V using Tapatalk
This. Just didn’t post it here. EVO Enforcer 4” lift and 35” BFG KO2s and Wild Boar grab handles because I am a shorty.
Sent from my iPhone using WAYALIFE mobile app
Sent from my iPhone using WAYALIFE mobile app
Cashburn
New member
Been waiting a long time for these... also RK 3.5 long arm pro lift going on same time[emoji16]
Sent from my iPhone using WAYALIFE mobile app
Kenthejeepguy
New member
critter812
New member
Installed my stinger on my 1/4 pounder!
CarolinaJK
New member
Installed some aluminum narrow PS flares. Currently replacing my CC tire carrier with an Evo hinged!
Sent from my iPhone using WAYALIFE mobile app
Sent from my iPhone using WAYALIFE mobile app
Attachments
Clutch
Caught the Bug
ihaveemerged
New member
New Rampage front bumper, rear still on order. Super happy with the look and feel. Keeping the winch mount portion off until the day comes that I get a winch
Sent from my iPhone using WAYALIFE mobile app
Dropped in a new jolt Box, the stock crappy battery went out at 2.5 years. 
Sent from my iPhone using WAYALIFE mobile app
Sent from my iPhone using WAYALIFE mobile app
CarolinaJK
New member
Nothing wrong with it at all. Just OCD took over and decided I needed all Evo.
*
Sent from my iPhone using WAYALIFE mobile app
-AINOKEA-
Hooked
Had to remove evo protek skids in prep for the dealer on Tuesday. Clutch getting replaced AGAIN under warranty. This time they doing slave cylinder as well. Not sure why they didn’t do it the first time but hey... as long as I’m not paying for it I’m fine with it for now.
Sent from my iPhone using WAYALIFE mobile app
Sent from my iPhone using WAYALIFE mobile app
AlStew
New member
AlStew
New member
Front shocks are done. So much cleaning and I really hope I didn’t forget something
Sent from my iPhone using WAYALIFE mobile app