Evo Rockskins with Bushwacker Flats

[Ddays]

Anyone running this setup? Photos?
I tried searching the forum but didn't see anything. I did a dry fit and looks like its going to be fun :crazyeyes:

 

[JK_Dave]

I've got the Evo rock skins with stock fenders and had no issues. As long as the BW fenders don't rise up higher than where the stock fenders are, you should be fine! :thumb:

 

[Ddays]

Unfortunately I believe they do sit a little higher. They have a beaded edge that seats against the body. I'm running into the same issue with the
rocker skins too.

 

[JK_Dave]

So how high do the rocker skins sit after you've installed the fenders and you hold the skins up against the body? The top of my skins is right below the body line where it curves and wraps up to the top, but you can probably try to match that line with the skin to get some more room, it just won't be much. You're also going to have a bit more gap around the corner potentially.

 

[Ddays]

Yeah, what I really need to do is put the painters tape on these so I can get a good dry fit. I held them up while trying to not scratch anything and it definitely looked like they will hit.
I'm not really worried about the rocker skins as much as the rear flares and Rockskins there.

If anyone has done this I'd love to see your pics!

 

[Grubbicon]

Found this on Google. It appears that it will work, but worst case you could always trim the opening on the corners just a bit.

 

[hinrichs]

I dont think I have any closeups anymore, but they fit fine. I never ran the extra rubber seal thing however so that could get in the way.

 

[Ddays]

Found this on Google. It appears that it will work, but worst case you could always trim the opening on the corners just a bit.

Thanks for looking that up! I googled but must have given up too soon. Your Jeep is one of the few I've seen with the tire carrier painted body color. I'm going back and forth on red or black. You have any photos of the rear to share? I looked on your profile page but didn't see any...

I dont think I have any closeups anymore, but they fit fine. I never ran the extra rubber seal thing however so that could get in the way.

Thanks, that's great to know. The rear corner skins were my biggest worry. I really wasn't looking forward to modifying either part back there. I can always remove that little bead if needed...

 

[hinrichs]

They will have less of a gap than the oem fenders do, but still look as good.

 

[Ddays]

Found this on Google. It appears that it will work, but worst case you could always trim the opening on the corners just a bit.

I just checked your youtube video out....how many trout did you guys take on after that water crossing!? :shock:
That guy in the white Jeep looked like he was in a hurry!!

 

[Grubbicon]

Found this on Google. It appears that it will work, but worst case you could always trim the opening on the corners just a bit.

I just checked your youtube video out....how many trout did you guys take on after that water crossing!? :shock:
That guy in the white Jeep looked like he was in a hurry!!

Lmao he definitely was hauling ass through there. Heres a few pictures of the carrier.

 

[Ddays]

Lmao he definitely was hauling ass through there. Heres a few pictures of the carrier.

That looks sharp as hell! I was going to paint my corners red and carrier black but if you don't mind a copycat I think I may do the same scheme
as you have there.

 

[Grubbicon]

Lmao he definitely was hauling ass through there. Heres a few pictures of the carrier.

That looks sharp as hell! I was going to paint my corners red and carrier black but if you don't mind a copycat I think I may do the same scheme
as you have there.

It doesnt bother me. Go for it if you want [emoji106]