Search results

Oh!!! Is that right ? ;) Have a look at this turd. It's a VW 2.0L with direct injection. It came into the shop for an MIL. It was missing on 3 and 4. The dealer put new plugs and #3 and #4 ignition coils. The customer said it ran worse after they worked on it. It took 2 days to soak this...

I prefer to use Techron in my vehicles. BG would be the best, but you can't buy it. Amaon has it for 14 bucks if you can't find it local. Buy the 20 OZ bottle. Lucas is snake oil :doh:

Intake air temp sensor should be on the intake snorkel tube. It's a two wire sensor and should have a black connector. Here's a shot of mine, but remember, mine is a 2016 3.6L. Yours will be different.

P0113-INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT HIGH For a complete wiring diagram, refer to the Wiring Information. Theory of Operation Intake Air Temperature Sensor performance looks at the outputs of three temperature sensors and compares them under cold start conditions. Following a...

Might be a pad wear scraper telling you it's time for pads ? OE, OEM and most good quality pads have a wear sensor. It functions well and works just like you stated. You can hear it rolling and it stops when the brake is applied.

I went out an took a shot of mine. Yours has oil/dirt buildup and I think that makes the lines stand out more. I was able to get one shot of the same area as in one of your pictures and it looks the same to me. Here's what I could capture for a visual comparison. If you look close you can see...

Here's an exploded view of the internals

Finished my rock sliders :clap2:

Possible Causes BATTERY CABLE HIGH RESISTANCE BATTERY CABLES TRANSMISSION IS NOT READING THE PROPER RANGE (AUTO) OR CLUTCH SWITCH IS NOT READING THE PROPER STATUS (MANUAL) OPEN FUSED BATTERY (+) CIRCUIT STARTER COIL DRIVER (INTERNAL TIPM) SKREEM CODES PRESENT STARTER MOTOR STARTER RELAY (T752)...

Most of these issues can be caused from sensor faults or terminal contact issues with high resistance. P0390-CAMSHAFT POSITION SENSOR CIRCUIT - BANK 2 SENSOR 2 NOTE: The CMP Sensor is a dual read sensor reading both camshafts of it's correlating bank. 3.2L/3.6L VVT Component Locations...

Certainly! The power comes from the MTIP (by the book) but you might know it as the TIPM and through the ASD relay. It powers fuse M19 on the gas rigs. Here's 2 circuit diagrams for you to reference :thumb:

The PCM controls the circuit. I'm not sure what the voltage will be coming from the PCM because it's not fed by a fuse. I would unplug the solenoid with the key on and check the voltage to the solenoid. I've also had issues when the vent solenoid gets filled with dirt and or the filter gets...

Mine isn't really a daily driver, but I do drive a lot back and forth to work when not driving my truck My choice was aluminum for weight reduction over steel. I also decided to run aluminum to eliminate the possibility of rust. I'm running raw aluminum with a clear coat paint to allow the raw...

This was my morning fun!

LOL! I've posted a few pics of my ride.

Yeah! Too bad nobody else can weld, fab or design :asshat: Narrow minded tools shouldn't work themselves into a lather over nothing, but, I guess you can help yourself when it comes to fanboy stuff. Enjoy! Originated from this thread...

I purchased the 2.5" Teraflex lift and like the ride. I'm gonna run Poison Spyder Crusher flares with 37's. I like the fact that I can use my Rubicon shocks with this low budget kit. I don't know what I'll do later, but for the cost of this 2.5" lift it's a no brainer for a starter lift. It has...

I looked at the HR, but didn't want leather and the 8.4 display audio system for an off road vehicle. While the trim level is nice, it's not worth it unless you can waste money on a mall krawler. I purchased the JKUR with an MSRP of $42K and promptly installed a 2.5 lift and 35's. Took it to...

2.5 inch lift with 35's. Waiting for my flat fenders and going 37's :yup:

I did the Rubicon JK Unlimited because it had the 4:1 transfer case gearing. Mine came with 3:73 gears, but they work okay with my 35's. I plan to change to 4:88's when I get the 37's. I have a TeraFlex 2.5 lift and find it works well for now. I have bigger plans later and the 2.5 kit was cheap...