Dynomax Quiet Crawler installed

deezus

deezus

New member
On the advice from a forum member, thanks , I ordered the DQC exhaust in separate pieces as the kit is back ordered and not available. It came out great, sounds good and is quiet and wasn't too hard to install. Had one cut at pipe going over axle and that's it. Here's a couple pics...1475628251801.jpg1475628262276.jpg1475628266757.jpg1475628271245.jpg

Sent from my SAMSUNG-SM-G930A using WAYALIFE mobile app
 
Which pieces did you use, specifically which pipe sections or cuts did you use. I like how yours came out.

I understand it is the first section of pipe that is unavailable.

Here are the original parts from the other post.
IMG_0738.jpg
 
I cut 55428 at the resonator, about 3 inches or so....52561, is that the part you say is unavailable? Because Amazon says it is...I used all the pieces on that diagram....51113 can probably be gotten cheaper at O'Reilly.
I got all my parts on Amazon.

Sent from my SAMSUNG-SM-G930A using WAYALIFE mobile app
 
Last edited:
Nicely done! Looks like it came out great and like you, I'm super happy with how it sounds :thumb:
 
wayoflife said:
Nicely done! Looks like it came out great and like you, I'm super happy with how it sounds :thumb:
Click to expand...
Yupyup thanks again Eddie! One thing though, the end pipe that goes over rear axle still isnt as tucked up as i would like, any suggestions? Wanna get one before it gets welded. Also, is it normal for a new exhaust to smell a lil funny at initial istall and run? And do i need to put anything between muffler/ resonator and jeep? Ty

Sent from my SAMSUNG-SM-G920A using WAYALIFE mobile app
 
deezus said:
Yupyup thanks again Eddie! One thing though, the end pipe that goes over rear axle still isnt as tucked up as i would like, any suggestions? Wanna get one before it gets welded. Also, is it normal for a new exhaust to smell a lil funny at initial istall and run? And do i need to put anything between muffler/ resonator and jeep? Ty

Sent from my SAMSUNG-SM-G920A using WAYALIFE mobile app
Click to expand...

Wish I could help you on getting the tail pipe up higher over the axle but I have mine dumping just before the axle. Sorry. As far as smell goes, you did make sure to remove the clear plastic protective covering on the muffler, right? Otherwise, yeah, an initial smell is pretty normal.
 
Yep this here.
In regards to the rear pipe, a lot of folks will make a cut so it doesn't "hang out" so far back...
:beer:


wayoflife said:
Wish I could help you on getting the tail pipe up higher over the axle but I have mine dumping just before the axle. Sorry. As far as smell goes, you did make sure to remove the clear plastic protective covering on the muffler, right? Otherwise, yeah, an initial smell is pretty normal.
Click to expand...
 
wayoflife said:
Wish I could help you on getting the tail pipe up higher over the axle but I have mine dumping just before the axle. Sorry. As far as smell goes, you did make sure to remove the clear plastic protective covering on the muffler, right? Otherwise, yeah, an initial smell is pretty normal.
Click to expand...
I thought that was a rock protection cover? So it stays shiny...😆

Sent from my SAMSUNG-SM-G930A using WAYALIFE mobile app
 
deezus said:
I cut 55428 at the resonator, about 3 inches or so....52561, is that the part you say is unavailable? Because Amazon says it is...I used all the pieces on that diagram....51113 can probably be gotten cheaper at O'Reilly.
I got all my parts on Amazon.

Sent from my SAMSUNG-SM-G930A using WAYALIFE mobile app
Click to expand...

Would you be able to tell me the diameter and length of that 51113 pipe? I got all the other parts in my shopping cart, just want to check the price of that at O'Reillys.
 
Thanks Deezus for posting this info.

Thanks Eddie for your original posts with the clips on how it sounds and that you still like it. Did you notice any performance changes?

Really liking this setup.
 
We saw nominal gains with this system, if I recall like 9-10HP and similar in TQ but keep in mind this is on a stock JK. The main advantage is just getting rid of the bulky OE setup.
:beer:

RMC2 said:
Thanks Deezus for posting this info.

Thanks Eddie for your original posts with the clips on how it sounds and that you still like it. Did you notice any performance changes?

Really liking this setup.
Click to expand...
 
Will this kit fit on a stock JKU? It says it fits:

"Unlimited Rubicon / Unlimited Sahara / Unlimited Sport

Fits Models with Rockcrawler Type Off-Road Suspension."

Thanks
 
notnalc68 said:
The U in JKU = Unlimited


Sent from my iPhone using WAYALIFE mobile app
Click to expand...

Of course I know that the U in JKU is for Unlimited. My question was if this kit will fit a STOCK jku or only lifted/rockcrawler suspension systems.

Can anyone confirm part numbers for the multiple 2.5 clamps in this kit?

I believe there are 2 clamps (part #35337) on each side of the catback then the other 3 clamps are part #36434 for the 3.6l?

Thanks
 
Last edited:
TxCoastie said:
Of course I know that the U in JKU is for Unlimited. My question was if this kit will fit a STOCK jku or only lifted/rockcrawler suspension systems.

Can anyone confirm part numbers for the multiple 2.5 clamps in this kit?

I believe there are 2 clamps (part #35337) on each side of the catback then the other 3 clamps are part #36434 for the 3.6l?

Thanks
Click to expand...

You can run it on a stock Jeep.


Sent from my iPhone using WAYALIFE mobile app
 
You must log in or register to reply here.
Top Bottom